Selleys Liquid Nails Exterior - 350g Construction product guide

AI Summary Product: Selleys Liquid Nails Exterior Brand: Selleys (a division of DuluxGroup (Australia) Pty Ltd) Category: Self-crosslinking acrylic construction adhesive (solvent-free, water-based) Primary Use: A high-performance construction adhesive specifically designed for outdoor use that can withstand heat, water, and UV. Mechanical fasteners can be removed after 4 hours. The bond will not crack or go brittle over time. Solvent-free with easy water clean-up. Ideal for decking, cladding, and fencing. Quick Facts

Best For: Exterior construction bonding — decking, cladding, fencing, and outdoor timber work. Also suitable for interior use. Key Benefit: 3 tonnes per m² after 4 hours on timber. Superior water, heat, and UV resistance. Bond won't crack or go brittle. Remove fasteners after 4 hours on porous surfaces. 500 tonnes per m² after 3 weeks. Form Factor: 350g cartridge, white paste (cures beige) Signal Word: ⚠️ Warning — H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. Application Method: Ensure surfaces are free from oil, grease, and dust. Apply a 5mm bead along joists, studs, or battens; on broad flat surfaces apply beads every 40cm. Immediately press firmly together; fix with nails, screws, or clamping. Allow minimum 4 hours before removing fasteners. Full bond strength 7 days. Not Suitable For: Metal (general use), rubber, marble, synthetic engineered timber, PTFE, PE, PP. Not for roofing or permanent water immersion. Not sole bonding agent for structural bonding. Avoid tightly clamped joints. Pre-test plastics. Note: Colorbond® is listed as a compatible material.

Common Questions This Guide Answers

What signal word and hazards apply? → Warning. H317 May cause an allergic skin reaction (Skin Sensitisation Category 1). H319 Causes serious eye irritation (Eye Damage/Irritation Category 2A). Effects may be delayed. What PPE is required? → Safety shoes, overalls, gloves (nitrile rubber), and safety glasses What materials can it bond? → Timber, particleboard, MDF, plywood, floor and wall panels, concrete, cement sheeting, masonry, tiles, ceramics, terracotta, plastics such as Perspex and PVC, Colorbond®, plasterboard, LOSP treated timber, glass What materials must NOT be bonded? → Metal (general), rubber, marble, synthetic engineered timber, PTFE, PE, PP. Not for roofing. How strong is it? → 3 tonnes/m² after 4 hours on timber; exceeds 1 MPa tensile shear at 24 hours; 3.5 MPa after 3 days; 500 tonnes/m² after 3 weeks When can fasteners be removed? → After 4 hours on porous surfaces. Expect longer for less porous surfaces and in cold or humid weather. Strong bond at 24 hours. Full bond strength 7 days. How long can materials be repositioned? → Up to 25 minutes Is it really weatherproof? → Superior water, heat, and UV resistance. Bond won't crack or go brittle over time. Service temperature up to 70°C. Not for permanent water immersion. What about VOC content? → Low VOC: 33 g/L. Meets Green Building Council limits for general purpose adhesives (less than 50 g/L). Solvent-free formulation. How do you clean up? → Uncured: water and soap. Cured: scraping or sanding.

Contents

Work Safely: This Product Is Classified WARNING Protect Yourself with the Required PPE Prepare for Success: Essential Setup Apply the Adhesive Allow Proper Cure Time Clean Up Know the Limitations Troubleshoot Common Problems Step-by-Step Application Summary Your Pre-Application Checklist First Aid Information References Product Facts Label Facts Summary Frequently Asked Questions

Product Facts AttributeValueProduct nameSelleys Liquid Nails ExteriorBrandSelleys (DuluxGroup)Recommended useConstruction adhesiveTechnologySelf-crosslinking acrylicPackaging350g cartridgeColourWhite (cures beige)FormPasteOdourMildSolvent-freeYesVOC content33 g/L (meets Green Building Council limits, less than 50 g/L)Density1.20 kg/LSpecific gravity1.2SolubilitySoluble in waterIndoor/OutdoorBoth (specifically designed for outdoor use)Ideal applicationsDecking, cladding, fencingSuitable materialsTimber, particleboard, MDF, plywood, floor & wall panels, concrete, cement sheeting, masonry, tiles, ceramics, terracotta, plastics (Perspex, PVC), Colorbond®, plasterboard, LOSP treated timber, glassNot suitable forMetal (general), rubber, marble, synthetic engineered timber, PTFE, PE, PPStrength at 4 hours3 tonnes/m² (on timber)Strength at 3 weeks500 tonnes/m²Initial bond (tensile shear)Exceeds 1 MPa at 24 hoursBond strength (tensile shear)3.5 MPa after 3 daysFastener removal (porous)4 hoursStrong bond24 hoursFull bond strength7 daysRepositionableUp to 25 minutesSkinning time20 minutes (weather dependent)Gap fillingUp to 5mmBead size5mmBead spacing (broad surfaces)Every 40cmCoverage~14 linear metres using a 5mm beadSag resistanceLess than 6mm (AS 2329-1999)PaintableAfter 24 hoursApplication temperature5°C to 40°CService temperatureUp to 70°CWater resistanceExcellent (not for permanent water immersion)UV resistanceYesHeat resistanceYesBond durabilityWon't crack or go brittle over timeClean-up (uncured)Water and soapClean-up (cured)Scraping or sandingStorageDry conditions, 5-25°C, protected from direct sunlightShelf lifeMinimum 12 months from date of manufactureComplianceAS 2329-1999; Green Building Council VOC limitsSignal wordWarningH317May cause an allergic skin reactionH319Causes serious eye irritationDangerous GoodsNON-Dangerous GoodsCombustibilityCombustible materialPPESafety shoes, overalls, gloves (nitrile rubber), safety glassesMade inAustralia

Frequently Asked Questions What is the product name: Selleys Liquid Nails Exterior What type of adhesive is it: Self-crosslinking acrylic construction adhesive, solvent-free What is the packaging: 350g cartridge What colour is the adhesive: White paste that cures beige What does the manufacturer describe it as: A high-performance construction adhesive specifically designed for outdoor use that can withstand heat, water, and UV What is it ideal for: Decking, cladding, and fencing Is it solvent-free: Yes — the formulation is solvent-free and allows for easy water clean-up What is the VOC content: 33 grams per litre. Meets Green Building Council VOC limits for general purpose adhesives (less than 50 g/L) What materials can it bond: Timber, particleboard, MDF and plywood, floor and wall panels, concrete, cement sheeting, masonry, tiles, ceramics, and terracotta, plastics such as Perspex and PVC, Colorbond®, plasterboard, LOSP treated timber, and glass Can it bond timber: Yes — including LOSP treated timber and wet timber (wipe off pooled water first) Can it bond Colorbond: Yes — Colorbond® is specifically listed as a compatible material Can it bond plastics: Yes — plastics such as Perspex and PVC. Pre-test other plastics for compatibility Can it bond concrete: Yes Can it bond tiles: Yes — tiles, ceramics, and terracotta Can it bond glass: Yes Can it bond metal: No — the manufacturer states "Do not use to adhere metal." Colorbond® (pre-coated steel) is the exception and is specifically listed as compatible Can it bond rubber: No — rubber is excluded Can it bond marble: No — marble is excluded Can it bond synthetic engineered timber: No — synthetic engineered timber is excluded Does it bond PTFE: No Does it bond polyethylene: No Does it bond polypropylene: No Can it be used for roofing: No — not recommended for roofing Can it be used for permanent water immersion: No Can it be used as sole structural bonding agent: No — do not use as the sole bonding agent for structural bonding Can it be used in tightly clamped joints: No — avoid using in tightly clamped joints (e.g. cabinet making joinery) Is it suitable for outdoor use: Yes — specifically designed for outdoor use. Can withstand heat, water, and UV. Is it suitable for indoor use: Yes — also suitable for interior applications What is the bond strength at 4 hours: 3 tonnes per m² on timber — at which point you can remove fasteners What is the bond strength at 24 hours: Exceeds 1 MPa in tensile shear. A strong bond is achieved. What is the bond strength at 3 days: 3.5 MPa in tensile shear What is the bond strength at 3 weeks: 500 tonnes per m² What is the full bond strength timing: 7 days When can mechanical fasteners be removed: After 4 hours on porous surfaces. Expect longer lead times for less porous surfaces and in cold or humid weather. How long is the repositioning window: Up to 25 minutes What is the skinning time: 20 minutes, weather dependent What is the maximum gap the adhesive can bridge: Up to 5mm What bead size should I use: 5mm diameter bead What bead spacing for broad flat surfaces: Every 40cm What is the coverage per cartridge: Approximately 14 linear metres using a 5mm diameter bead What is the sag resistance: Less than 6mm, tested to AS 2329-1999 Appendix A Does the bond crack or go brittle: No — the bond will not crack or go brittle over time Is it UV resistant: Yes — superior UV resistance for exterior applications Is it heat resistant: Yes — service temperature up to 70°C Is it water resistant: Yes — excellent water resistance. Not for permanent water immersion. Is it paintable: Yes, after 24 hours What is the application temperature range: 5°C to 40°C What is the service temperature: Up to 70°C What compliance standards does it meet: AS 2329-1999 construction adhesive standards, and Green Building Council VOC limits for general purpose adhesives What is the signal word: Warning What are the hazard statements: H317 May cause an allergic skin reaction; H319 Causes serious eye irritation Is it a skin sensitiser: Yes — Skin Sensitisation Category 1. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Effects may be delayed. What PPE is required: Safety shoes, overalls, gloves (nitrile rubber), and safety glasses Is a respirator required: No — natural ventilation is adequate under normal use conditions Is it a Dangerous Good: No — classified as NON-Dangerous Goods Is it combustible: Yes — combustible material How do I clean up uncured adhesive: Water and soap How do I clean up cured adhesive: Scraping or sanding How should it be stored: In dry conditions, protected from direct sunlight, between 5°C and 25°C What is the shelf life: Minimum 12 months from date of manufacture when stored in appropriate conditions What are the emergency telephone numbers: Australia 1800 220 770; New Zealand 0800 220 770 What is the Poisons Information Centre number: Australia 131 126; New Zealand 0800 764 766

Selleys Liquid Nails Exterior: Your Complete Application Guide Selleys Liquid Nails Exterior is a high-performance construction adhesive specifically designed for outdoor use. It can withstand heat, water, and UV — making it ideal for decking, cladding, and fencing applications. The bond will not crack or go brittle over time, even under Australia's demanding exterior conditions. This adhesive delivers 3 tonnes per m² after just 4 hours on timber, at which point you can remove mechanical fasteners. It continues to strengthen — exceeding 1 MPa tensile shear at 24 hours, reaching 3.5 MPa at 3 days, and achieving 500 tonnes per m² after 3 weeks. Full bond strength develops at 7 days. The solvent-free, self-crosslinking acrylic formulation is low VOC (33 g/L, meeting Green Building Council limits), allows easy water clean-up, and is paintable after 24 hours. It bonds a wide range of building materials: timber, particleboard, MDF, plywood, floor and wall panels, concrete, cement sheeting, masonry, tiles, ceramics, terracotta, plastics such as Perspex and PVC, Colorbond®, plasterboard, LOSP treated timber, and glass. Compared to standard Liquid Nails products, Exterior is engineered specifically to last in all weather — superior water, heat, and UV resistance with a service temperature up to 70°C. It complies with AS 2329-1999 construction adhesive standards. ⚠️ WARNING — Read the safety section before use. This product is a skin sensitiser. Important — Know the limitations before you start:

Do not use to adhere metal (general), rubber, marble, or synthetic engineered timber Not suitable for PTFE (Teflon®), polyethylene, or polypropylene — pre-test other plastics Not recommended for roofing Not for permanent water immersion (water resistant, not waterproof) Do not use as the sole bonding agent for structural bonding Avoid tightly clamped joints (e.g. cabinet making joinery) Note: Colorbond® (pre-coated steel) is specifically listed as compatible — this is the exception to the general metal exclusion

Work Safely: This Product Is Classified WARNING Selleys Liquid Nails Exterior is hazardous according to the criteria of Safe Work Australia GHS 7. The signal word is Warning. It is classified as NON-Dangerous Goods. This product carries two hazard statements: CodeStatementWhat This MeansH317May cause an allergic skin reactionSkin Sensitisation Category 1. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Effects may be delayed — you may not notice a reaction immediately.H319Causes serious eye irritationEye Damage/Irritation Category 2A. Reversible effects to eyes. The product is combustible material but is NOT classified as Dangerous Goods for transport. Key precautionary statements:

P261: Avoid breathing dust, fume, gas, mist, vapours, or spray P264: Wash hands, face, and all exposed skin thoroughly after handling P272: Contaminated work clothing should not be allowed out of the workplace P280: Wear protective gloves/protective clothing including eye/face protection

Protect Yourself with the Required PPE The required personal protection equipment is: SAFETY SHOES, OVERALLS, GLOVES, SAFETY GLASSES. Gloves: Nitrile rubber gloves should be suitable for intermittent contact. Due to variations in glove construction and local conditions, make a final assessment based on your situation. This is particularly important given the H317 skin sensitisation hazard — bare-skin contact should be avoided. Safety glasses: The product is classified Eye Damage/Irritation Category 2A (H319 serious eye irritation). Overalls and safety shoes: Full body coverage minimises skin contact. Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing and other protective equipment before storing or re-using. Respirator: Not required. Natural ventilation is adequate under normal use conditions. The product is solvent-free with mild odour. Hygiene: Always wash hands before smoking, eating, drinking, or using the toilet. Do not eat, drink, or smoke when using this product. Keep away from food, drink, and animal feeding stuffs. Ensure that eyewash stations and safety showers are close to the workstation location.

Prepare for Success: Essential Setup Gather your tools and prepare surfaces before opening the adhesive. Essential Equipment:

Caulking gun Utility knife or scissors for cutting the cartridge tip and nozzle Nails, screws, clamps, or bracing materials (required during cure) Water and soap for clean-up of uncured adhesive Full PPE: safety shoes, overalls, nitrile rubber gloves, safety glasses Scrap material matching your project substrate for practice beads

Surface Preparation: Ensure surfaces are free from oil, grease, and dust. Wipe off any pooled water from wet timber. Both bonding surfaces must be clean. The adhesive adheres to wet and dry timber, but pooled water must be removed first. Verify material compatibility before applying. Check that your substrates are on the approved list. In particular:

Do not use on metal (general), rubber, marble, or synthetic engineered timber Pre-test plastics for compatibility — Perspex and PVC are confirmed compatible; PTFE, PE, and PP are not suitable Colorbond® (pre-coated steel) is specifically listed as compatible — this does not extend to bare metals generally

Apply the Adhesive

Cut cartridge tip, fit nozzle, and cut to desired opening to achieve a 5mm bead. Load the cartridge into the caulking gun.

Apply a 5mm bead of Liquid Nails Exterior using a caulking gun along the length of joist, stud, or batten. On broad flat surfaces, apply beads every 40cm. Immediately press the two surfaces firmly together. Fix with sufficient nails, screws, or clamping to hold load and achieve contact over the total bond area. Materials are repositionable for up to 25 minutes — adjust positioning within this window. Allow adhesive to set (minimum 4 hours) before removing any temporary fasteners or clamping. Expect longer lead times for less porous surfaces and in cold or humid weather. Coverage: Each 350g cartridge provides approximately 14 linear metres using a 5mm diameter bead. Gap filling: The adhesive bridges gaps up to 5mm. If substrate irregularities exceed 5mm, prepare the surface to reduce the gap before application. Skinning time: The adhesive skins in approximately 20 minutes (weather dependent). Work within this window for optimal transfer and bond development. Flow and transfer exceeds 75% after 15 minutes drying, tested to AS 2329-1999 Appendix B. Important: Do not use as the sole bonding agent for structural bonding. Use with mechanical fasteners in high stress applications.

Allow Proper Cure Time Selleys Liquid Nails Exterior develops strength progressively: StageTimeSpecificationFastener removal (porous)4 hours3 tonnes/m² on timberStrong bond24 hoursExceeds 1 MPa tensile shearBond strength3 days3.5 MPa tensile shearFull bond strength7 days—Maximum strength3 weeks500 tonnes/m² Key notes:

The 4-hour fastener removal specification applies to porous surfaces. Expect longer lead times for less porous surfaces and in cold or humid weather. A strong bond is achieved in 24 hours. Paintable after 24 hours. The adhesive meets AS 2329-1999 accelerated ageing requirements after 500 hours at 70°C, confirming long-term bond durability. Static load in shear exceeds 24 hours sustaining a 40N load at 40°C (AS 2329-1999 Appendix G).

Clean Up Uncured adhesive: Remove with water and soap. Wipe tools, surfaces, and any squeeze-out promptly while adhesive is still wet. The solvent-free, water-based formulation makes outdoor clean-up straightforward. Cured adhesive: Once cured, the adhesive cannot be dissolved with water. Remove by scraping or sanding. Skin contact: Effects may be delayed. If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. If swelling, redness, blistering, or irritation occurs, seek medical assistance. Disposal: Cure product before disposal. Avoid contaminating waterways. Empty cartridges may be disposed via local landfill. If spilt, absorb with clay, sand, or earth. Collect and seal in properly labelled container. Dispose according to local authority regulations. Do not dispose down drains or into waterways.

Know the Limitations Selleys Liquid Nails Exterior has specific limitations that must be respected:

Do not use to adhere metal (general), rubber, marble, or synthetic engineered timber — Colorbond® (pre-coated steel) is the specific exception for metal substrates Not suitable for PTFE (Teflon®), polyethylene, or polypropylene — pre-test other plastics for compatibility Not recommended for roofing Not for permanent water immersion — excellent water resistance, but not waterproof for submersion Do not use as the sole bonding agent for structural bonding — use with mechanical fasteners Avoid using in tightly clamped joints (e.g. cabinet making joinery) Expect longer cure times for less porous surfaces and in cold or humid weather The 3 tonnes/m² and 500 tonnes/m² strength specifications are measured on timber substrates

Troubleshoot Common Problems Problem: Adhesive won't dispense despite trigger pressure Nozzle blocked with cured adhesive. Cut nozzle to expose fresh adhesive, or replace cartridge if product has exceeded shelf life (minimum 12 months from manufacture when stored properly). Problem: Materials won't stay in position Ensure sufficient mechanical fasteners (nails, screws, or clamping) are in place to hold load and achieve contact over the total bond area. The adhesive has less than 6mm sag resistance, but mechanical support is required during the cure period. Remember: repositionable for up to 25 minutes. Problem: Adhesive skinning before surfaces are joined Skinning occurs at approximately 20 minutes (weather dependent). In hot or dry conditions, work faster or in smaller sections. Apply adhesive and immediately press surfaces together as directed. Problem: Slow bond development The 4-hour fastener removal specification applies to porous surfaces. Less porous surfaces, cold weather, and high humidity all extend cure times. A strong bond is achieved in 24 hours, with full bond strength at 7 days. Problem: Bond failure on plastics Pre-test all plastics for compatibility before committing. Perspex and PVC are confirmed compatible. PTFE, polyethylene, and polypropylene are not suitable. Other plastics vary. Problem: Bond failure on metal substrate Check: is the substrate Colorbond® (pre-coated steel)? Colorbond® is specifically listed as compatible. General metals, however, are excluded. The manufacturer states: "Do not use to adhere metal." If you need to bond bare metal, use a product specifically rated for metal adhesion such as Selleys Liquid Nails Heavy Duty.

Step-by-Step Application Summary

Put on full PPE: Safety shoes, overalls, nitrile rubber gloves, and safety glasses. Verify material compatibility: Confirm substrates are on the approved list. No metal (except Colorbond®), rubber, marble, or synthetic engineered timber. Prepare surfaces: Ensure surfaces are free from oil, grease, and dust. Wipe off any pooled water from wet timber. Cut nozzle to achieve a 5mm bead opening. Apply a 5mm bead along the length of joist, stud, or batten. On broad flat surfaces, apply beads every 40cm. Immediately press surfaces firmly together. Fix with sufficient nails, screws, or clamping to hold load and achieve contact over the total bond area. Materials are repositionable for up to 25 minutes. Allow adhesive to set: minimum 4 hours (porous surfaces) before removing temporary fasteners. Expect longer for less porous surfaces and in cold or humid weather. Strong bond: 24 hours. Full bond strength: 7 days. Maximum strength: 3 weeks (500 tonnes/m²). Paintable after 24 hours. Clean up uncured adhesive with water and soap. Cured adhesive: scraping or sanding.

Your Pre-Application Checklist Safety:

Full PPE on: safety shoes, overalls, nitrile rubber gloves, safety glasses Aware of H317 skin sensitisation hazard — avoid bare-skin contact; effects may be delayed Eyewash station and safety shower close to workstation Water and soap staged for clean-up and skin decontamination

Materials:

Confirmed: no metal (general), rubber, marble, or synthetic engineered timber in the project Confirmed: no PTFE, polyethylene, or polypropylene Confirmed: Colorbond® is the only metal-type substrate being bonded (if applicable) Confirmed: not for roofing or permanent water immersion Confirmed: not sole bonding agent for structural applications — mechanical fasteners planned Confirmed: not a tightly clamped joint (e.g. cabinet making joinery) Plastics pre-tested for compatibility (Perspex and PVC confirmed OK) Surfaces free from oil, grease, and dust Pooled water wiped from wet timber Nails, screws, clamps, or bracing staged

Application:

Caulking gun loaded and tested on scrap material Nozzle cut to 5mm bead opening Practice bead completed on scrap substrate Bead spacing planned: every 40cm on broad flat surfaces Application temperature between 5°C and 40°C Weather conditions suitable — no rain expected during 4-hour minimum cure Cartridge within shelf life (minimum 12 months from manufacture) Timer available: minimum 4 hours before removing fasteners

First Aid Information In case of emergency, refer to the Safety Data Sheet. Key first aid measures: If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766). Inhalation: Remove victim from exposure — avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice if effects persist. Skin contact: Effects may be delayed. If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. If swelling, redness, blistering, or irritation occurs, seek medical assistance. Eye contact: If in eyes, hold eyelids apart and flush the eyes continuously with running water. Continue flushing until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes. Transport to doctor or hospital. Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by mouth to an unconscious patient. If vomiting occurs, give further water. Seek medical advice. PPE for first aiders: Wear safety shoes, overalls, gloves, and safety glasses. Emergency telephone: Australia — 1800 220 770; New Zealand — 0800 220 770.

References

Selleys Liquid Nails Exterior Technical Data Sheet (Version 1.0, 2023) — Product description, key features, uses, technical information, application instructions, limitations, clean-up Selleys Liquid Nails Exterior Safety Data Sheet (Version 1.2, 14 June 2023, Ref: SELGHSEN001395) — Hazard identification, PPE requirements, first aid, composition, handling/storage, physical properties, toxicological information Selleys Liquid Nails Exterior Product Page — Product features, technical details, limitations, directions for use

Label Facts Summary

Disclaimer: All facts and statements below are sourced from official Selleys documentation (Technical Data Sheet, Safety Data Sheet, and Product Page). Consult the full SDS and TDS for complete information. This is not professional safety advice.

Verified Label Facts

Product name: Selleys Liquid Nails Exterior Brand: Selleys (a division of DuluxGroup (Australia) Pty Ltd) ABN: 67 000 049 427 Recommended use: Construction adhesive Technology: Self-crosslinking acrylic Formulation: Solvent-free Packaging: 350g cartridge Colour: White (cures beige) Form: Paste Odour: Mild Density: 1.20 kg/L Specific gravity: 1.2 Solubility: Soluble in water VOC content: 33 g/L (meets Green Building Council limits, less than 50 g/L) Ideal for: Decking, cladding, fencing Suitable materials: Timber, particleboard, MDF, plywood, floor & wall panels, concrete, cement sheeting, masonry, tiles, ceramics, terracotta, plastics (Perspex, PVC), Colorbond®, plasterboard, LOSP treated timber, glass Not suitable for: Metal (general), rubber, marble, synthetic engineered timber, PTFE, PE, PP Not for: Roofing, permanent water immersion Do not use as: Sole bonding agent for structural bonding Avoid: Tightly clamped joints (cabinet making joinery) Pre-test: Other plastics for compatibility Note: Colorbond® is specifically listed as compatible (exception to general metal exclusion) Strength at 4 hours: 3 tonnes/m² on timber Strength at 3 weeks: 500 tonnes/m² Initial bond tensile shear: Exceeds 1 MPa at 24 hours Bond strength tensile shear: 3.5 MPa after 3 days Static load shear: Exceeds 24h sustaining 40N at 40°C (AS 2329-1999 Appendix G) Accelerated ageing: Meets/exceeds after 500h at 70°C (AS 2329-1999 Appendix E) Fastener removal (porous): 4 hours Strong bond: 24 hours Full bond strength: 7 days Maximum strength: 3 weeks Repositionable: Up to 25 minutes Skinning time: 20 minutes (weather dependent) Flow and transfer: Exceeds 75% after 15 min (AS 2329-1999 Appendix B) Gap filling: Up to 5mm Sag resistance: Less than 6mm (AS 2329-1999 Appendix A) Bead size: 5mm Bead spacing (broad surfaces): Every 40cm Coverage: ~14 linear metres per 5mm bead Paintable: After 24 hours Application temperature: 5°C to 40°C Service temperature: Up to 70°C Water resistance: Excellent (not permanent immersion) UV resistance: Yes Heat resistance: Yes Bond durability: Won't crack or go brittle over time All weather: Yes No sag or stringing: Yes For wet and dry timber: Yes Clean-up uncured: Water and soap Clean-up cured: Scraping or sanding Storage: Dry conditions, 5-25°C, protected from direct sunlight Shelf life: Minimum 12 months from manufacture Compliance: AS 2329-1999, Green Building Council VOC limits Signal word: Warning Hazard: Eye Damage/Irritation Category 2A Hazard: Sensitisation - Skin - Category 1 H317: May cause an allergic skin reaction H319: Causes serious eye irritation Allergic contact dermatitis: Repeated or prolonged skin contact may lead to allergic contact dermatitis Effects may be delayed: Yes Dangerous Goods: NON-Dangerous Goods Combustibility: Combustible material PPE: Safety shoes, overalls, gloves (nitrile rubber), safety glasses Engineering: Natural ventilation adequate under normal use conditions Composition: Epoxypropoxy silane <1%, Benzotriazole derivatives <1%, BIT/MIT/CMIT/OIT each <0.05% Made in: Australia

General Product Claims

High-performance construction adhesive specifically designed for outdoor use Can withstand heat, water, and UV Mechanical fasteners can be removed after 4 hours Bond will not crack or go brittle over time Solvent-free with easy water clean-up Low VOC Engineered to last in all weather Superior water, heat, and UV resistance for exterior applications Adheres 3 tonnes per m² after 4 hours on timber 500 tonnes per m² after 3 weeks All weather bonding No sag or stringing Paintable once cured For wet and dry timber Retains high strength even in extreme weather Ideal for decking, cladding, fencing Made in Australia