Liquid Nails Construction Adhesive - Selleys product guide

AI Summary Product: Selleys Liquid Nails Original Brand: Selleys (a division of DuluxGroup (Australia) Pty Ltd) Category: Solvent-based construction adhesive Primary Use: High strength multipurpose construction adhesive that forms a strong and lasting bond on most building substrates, suitable for timber, plasterboard, MDF, particleboard, masonry, concrete, tiles, ceramics, metals, plastics, rubber, and glass. Quick Facts

Best For: Bonding building materials in construction, renovation, and repair applications — indoors and outdoors Key Benefit: High strength, flexible, water and weather resistant bond on most building substrates, suitable for wet and dry timber Form Factor: Brown/beige paste in Tube 100g, Cartridge 320g, Cartridge 375mL, or Sausage 680g Application Method: Cut cartridge tip to 5mm opening, fit nozzle. Apply bead along joists, studs, or battens; on broad flat surfaces apply beads every 40cm in a zig-zag pattern. Press firmly, fix with sufficient nails, screws, or clamping. Repositionable for up to 20 minutes. Minimum 24 hours before removing temporary fasteners. Full cure in 7 days. Not Suitable For: Polyethylene, polypropylene, Teflon®, styrene foam, mirrors, metals heated by direct sunlight, permanent water immersion, or as the sole bonding agent for structural bonding. Avoid tightly clamped joints (e.g. cabinet making joinery).

Common Questions This Guide Answers

What materials can Selleys Liquid Nails Original bond? → Timber, plasterboard, MDF, particleboard, masonry, concrete, tiles, ceramics, metals, plastics*, rubber, and glass How long before I can remove temporary fasteners? → Minimum 24 hours; a strong bond is usually achieved in 24 hours and continues to strengthen over 2–3 days When does the adhesive reach full strength? → Cures in 7 days; tensile strength 1MPa after 7 days cure (AS2329) How long can I reposition materials after fitting? → Repositionable for up to 20 minutes after fitting What bead spacing should I use on broad flat surfaces? → Apply beads every 40cm How much coverage per cartridge? → Approximately 3 metres using a 5mm diameter bead What safety equipment is required? → Safety shoes, overalls, gloves (nitrile rubber), safety glasses, and respirator. If inhalation risk exists, wear organic vapour/particulate respirator per AS/NZS 1715 and AS/NZS 1716 What hazards does this product present? → Signal word: Danger. Highly flammable liquid and vapour (H225). Causes damage to organs (H370). Causes skin irritation (H315). Causes serious eye irritation (H319). Dangerous Goods Class 3 How do I clean up? → Uncured product: mineral turpentine. Cured product: scraping or sanding What can it NOT bond? → Not suitable for polyethylene, polypropylene, Teflon®, styrene foam, or mirrors. Not for metals heated by direct sunlight. Not for permanent water immersion. Not as sole bonding agent for structural bonding. Avoid tightly clamped joints.

Contents

Work Safely: Understand the Hazards Before You Start Prepare for Success: Essential Setup Load Your Caulking Gun the Right Way Practice Your Bead Control on Scrap Material Apply the Right Amount in the Right Pattern Position Materials and Fix in Place Allow Proper Cure Time Clean Up Know the Limitations Troubleshoot Common Problems Step-by-Step Application Summary Your Pre-Application Checklist First Aid Information References Product Facts Label Facts Summary Frequently Asked Questions

Product Facts AttributeValueProduct nameSelleys Liquid Nails OriginalBrandSelleys (DuluxGroup)ColourBrown / BeigeAdhesive typeSolvent-based construction adhesivePackage sizesTube 100g, Cartridge 320g, Cartridge 375mL, Sausage 680gSuitable materialsTimber, plasterboard, MDF, particleboard, masonry, concrete, tiles, ceramics, metals, plastics*, rubber, glassIndoor/Outdoor useIndoor and outdoorWater resistanceExcellentStrengthHigh strength (Tensile 1MPa after 7 days, AS2329)Sag resistance (AS2329)Less than 6mmDensity1.15Cure time (strong bond)24 hours (continues strengthening 2–3 days)Cure time (full strength)7 daysCoverageApproximately 3m using a 5mm diameter beadRepositioning timeUp to 20 minutes after fittingBead spacing (broad surfaces)Every 40cmNozzle opening5mmPaintableYes, when fully curedApplication temperature5°C to 35°CService temperature-20°C to 100°CStandard complianceAustralian Standard AS-2329 (1999)Clean-up (uncured)Mineral turpentineClean-up (cured)Scraping or sandingSignal wordDangerHazard classificationsFlammable Liquids Cat 2, Skin Irritation Cat 2, Eye Irritation Cat 2A, STOT-SE Cat 1Key hazard statementsH225 Highly flammable liquid and vapour; H370 Causes damage to organs; H315 Causes skin irritation; H319 Causes serious eye irritationDangerous Goods Class3 (Flammable Liquid)UN No1133Flash point-15°CPPE requiredSafety shoes, overalls, nitrile gloves, safety glasses, respirator (AS/NZS 1715 and 1716)Marine pollutantYesMade inAustraliaConditionNewCurrencyAUD

Frequently Asked Questions What is the product name: Selleys Liquid Nails Original What type of adhesive is it: Solvent-based construction adhesive What does the manufacturer describe it as: High strength multipurpose construction adhesive that forms a strong and lasting bond on most building substrates What package sizes are available: Tube 100g, Cartridge 320g, Cartridge 375mL, Sausage 680g What colour is the adhesive: Brown / Beige What materials can it bond: Timber, plasterboard, MDF, particleboard, masonry, concrete, tiles, ceramics, metals, plastics*, rubber, and glass Can it bond timber: Yes Can it bond plasterboard: Yes Can it bond MDF: Yes Can it bond particleboard: Yes Can it bond masonry: Yes Can it bond concrete: Yes Can it bond tiles: Yes Can it bond ceramics: Yes Can it bond metals: Yes, but not metals heated by direct sunlight — bonds weaken at higher temperatures; use Liquid Nails Mirror Metal and Glass instead Can it bond plastics: Yes, most plastics Can it bond rubber: Yes Can it bond glass: Yes Does it bond polyethylene: No — not suitable for polyethylene Does it bond polypropylene: No — not suitable for polypropylene Does it bond Teflon: No — not suitable for Teflon Can it bond styrene foam: No — not suitable for styrene foam; use Liquid Nails Fast Grab instead Can it be used on mirrors: No — not suitable for mirrors; use Liquid Nails Mirror Metal and Glass instead Can it be used for structural bonding alone: No — do not use as the sole bonding agent for structural bonding Can it be used in tightly clamped joints: No — avoid use in tightly clamped joints such as cabinet making joinery Can it be submerged in water permanently: No — not suitable for permanent water immersion Does it work on wet timber: Yes Does it work on dry timber: Yes Is the bond flexible after curing: Yes Is it water and weather resistant: Yes Is it paintable: Yes, when fully cured Can it be used indoors and outdoors: Yes Is it easily extrudable at low temperatures: Yes What nozzle opening size is recommended: 5mm What bead spacing for broad flat surfaces: Every 40cm What application pattern is recommended: Bead along length of joist, stud, or batten; zig-zag pattern on broad surfaces with beads every 40cm How much coverage per 5mm bead: Approximately 3 metres How long is the repositioning window: Up to 20 minutes after fitting How should materials be fixed after positioning: With sufficient nails, screws, or clamping to hold load and achieve contact over total bond area Should mechanical fasteners be used: Yes, use with mechanical fasteners in high stress applications How long before removing temporary fasteners: Minimum 24 hours How long for a strong bond: Usually 24 hours, continues strengthening over 2–3 days How long for full cure: 7 days — expect longer times for thicker applications, less porous surfaces, and in cold weather What is the tensile strength: 1MPa after 7 days cure (AS2329) What is the sag resistance: Less than 6mm (AS2329) What standard does it meet: Australian Standard AS-2329 (1999) What is the application temperature range: 5°C to 35°C What is the service temperature range: -20°C to 100°C What is the flash point: -15°C What is the signal word: Danger What are the hazard statements: H225 Highly flammable liquid and vapour; H315 Causes skin irritation; H319 Causes serious eye irritation; H370 Causes damage to organs What is the STOT-SE classification: Category 1 — Causes damage to organs (H370) What Dangerous Goods class is it: Class 3 (Flammable Liquid) What PPE is required: Safety shoes, overalls, gloves (nitrile rubber), safety glasses, and respirator What respirator standard applies: Organic vapour/particulate respirator meeting AS/NZS 1715 and AS/NZS 1716 where inhalation risk exists What glove material is recommended: Nitrile rubber, suitable for intermittent contact What engineering ventilation is needed: Natural ventilation should be adequate under normal use conditions What clean-up solvent is used for uncured adhesive: Mineral turpentine How is cured adhesive removed: By scraping or sanding What surface preparation is required: Ensure surfaces are free from oil, grease, and dust; wipe off any pooled water from wet timber Is it a marine pollutant: Yes What is the UN number: 1133 What is the Hazchem code: 3Y What are the emergency telephone numbers: Australia 1800 220 770; New Zealand 0800 220 770 What is the Poisons Information Centre number: Australia 131 126; New Zealand 0800 764 766 What is the density: 1.15 What is the specific gravity: 1.12 to 1.16 Is vapour heavier than air: Yes, relative vapour density greater than 1 What are the main chemical components: Naphtha petroleum hydrotreated light (10–30%) and Phenol 2,2-methylenebis[6-(1,1-dimethylethyl)-4-methyl] (less than 1%) How should it be stored: In a cool, dry, well-ventilated place, out of direct sunlight, away from foodstuffs and sources of heat or ignition, stored locked up, container standing upright, closed when not in use What should I do if the product gets in my eyes: Hold eyelids apart and flush eyes continuously with running water for at least 15 minutes; seek medical attention What should I do if I inhale the vapour: Remove from exposure, keep warm, keep at rest until fully recovered; seek medical advice if effects persist What should I do if it contacts my skin: Remove contaminated clothing immediately and flush skin with running water for 15 minutes; seek medical assistance if irritation occurs

Master Selleys Liquid Nails Original: Your Guide to Professional Bonds Selleys Liquid Nails Original is a high strength multipurpose construction adhesive that forms a strong and lasting bond on most building substrates. This solvent-based adhesive works on timber, plasterboard, MDF, particleboard, masonry, concrete, tiles, ceramics, metals, plastics, rubber, and glass. It bonds wet and dry timber, stays flexible after curing, and resists water and weather once fully set. It extrudes easily even at low temperatures, so you won't fight with it in cold conditions. You've got four packaging options: 100g tubes for small repairs, 320g cartridges for standard projects, 375mL cartridges, and 680g sausages for higher-volume work. The cartridges and sausages dispense with a caulking gun, giving you the mechanical control needed for consistent application. Getting good results comes down to proper technique, correct materials, and respecting the cure time. The adhesive is repositionable for up to 20 minutes after fitting, giving you a generous working window — but success starts with preparation. Important — Know the limitations before you start:

Not suitable for polyethylene, polypropylene, or Teflon® Not suitable for styrene foam (use Liquid Nails Fast Grab instead) Not suitable for mirrors (use Liquid Nails Mirror Metal and Glass instead) Not suitable for metals heated by direct sunlight — bonds weaken at higher temperatures (use Liquid Nails Mirror Metal and Glass instead) Do not use as the sole bonding agent for structural bonding Avoid tightly clamped joints (e.g. cabinet making joinery) Not suitable for permanent water immersion

Work Safely: Understand the Hazards Before You Start This Product Is Classified Danger Selleys Liquid Nails Original is hazardous according to Safe Work Australia GHS 7 and is classified as Dangerous Goods Class 3 (Flammable Liquid). The signal word is Danger. The identified hazard classifications and statements are: Flammable Liquids — Category 2: H225 Highly flammable liquid and vapour. The flash point is -15°C, meaning this product can ignite well below room temperature. Specific Target Organ Toxicity (Single Exposure) — Category 1: H370 Causes damage to organs. This is the most severe single-exposure organ toxicity classification. A single overexposure can cause organ damage. This hazard demands strict adherence to PPE requirements and ventilation controls. Skin Corrosion/Irritation — Category 2: H315 Causes skin irritation. Eye Damage/Irritation — Category 2A: H319 Causes serious eye irritation. Protect Yourself with the Full Required PPE The required personal protection equipment is: SAFETY SHOES, OVERALLS, GLOVES, SAFETY GLASSES, RESPIRATOR. Respirator: If an inhalation risk exists, wear an organic vapour/particulate respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716. Do not breathe dust, fume, gas, mist, vapours, or spray. Natural ventilation should be adequate under normal use conditions — however, given the H370 organ damage classification, you should assess your specific work environment and err on the side of respiratory protection. Safety glasses: The product causes serious eye irritation (Category 2A). Wear safety glasses with side shields. Ensure eyewash stations are close to the workstation. Gloves: Nitrile rubber gloves should be suitable for intermittent contact. Due to variations in glove construction and local conditions, make a final assessment based on your specific situation. Keep spare pairs accessible. Overalls and safety shoes: Full body coverage protects against skin contact, which causes irritation (Category 2). Wash contaminated clothing and protective equipment before storing or re-using. Hygiene: Always wash hands before smoking, eating, drinking, or using the toilet. Do not eat, drink, or smoke when using this product. Keep away from food, drink, and animal feeding stuffs. Avoid contact with clothing, eyes, and skin. Fire Safety This product is a highly flammable liquid and vapour with a flash point of -15°C. It may form flammable vapour mixtures with air. Vapour may travel a considerable distance to a source of ignition and flash back. All potential sources of ignition — open flames, pilot lights, furnaces, spark-producing switches, and electrical equipment — must be eliminated both in and near the work area. Do not smoke. Use explosion-proof electrical, ventilating, lighting, and all other equipment. Use non-sparking tools. Ground and bond container and receiving equipment. Take action to prevent static discharges. Nearby equipment must be earthed. Electrical requirements for the work area should be assessed according to AS3000. Keep a suitable fire extinguisher accessible: alcohol resistant foam or dry agent (carbon dioxide, dry chemical powder). Ventilation Natural ventilation should be adequate under normal use conditions. For indoor applications, ensure good airflow — open windows and doors. Vapour is heavier than air (relative vapour density greater than 1), so prevent vapour concentration in hollows, pits, or low-lying areas. If working in confined or poorly ventilated spaces, increase ventilation and wear the full respiratory protection specified above. If you experience headache, dizziness, or nausea, ventilation is insufficient — move to fresh air immediately. Prepare for Success: Essential Setup Get your complete toolkit together and prepare surfaces before opening the adhesive. Preparation makes the difference between clean, controlled results and a frustrating mess. Essential Equipment:

Caulking gun: manual skeleton type for 320g cartridges, or sausage gun for 680g sausages Utility knife or scissors for cutting the cartridge tip Clean rags or paper towels Mineral turpentine for clean-up of uncured adhesive Nails, screws, clamps, weights, or bracing materials appropriate to your project Full PPE: safety shoes, overalls, nitrile rubber gloves, safety glasses, respirator Scrap material matching your project substrate for practice beads Fire extinguisher accessible (alcohol resistant foam or dry agent)

Surface Preparation: Ensure surfaces are free from oil, grease, and dust. Wipe off any pooled water from wet timber. Both bonding surfaces must be clean and free of contaminants. Use a stiff brush to remove dust from porous surfaces like concrete or masonry. Wipe non-porous surfaces (metals, plastics, glass) with a clean cloth to eliminate oils or residues. The adhesive bonds to the material itself, not to dirt or previous coatings. For wet timber, the product works on both wet and dry wood — but wipe off any pooled water first. Do not apply to visibly dripping or frost-covered surfaces. Load Your Caulking Gun the Right Way For 320g or 375mL Cartridges:

Release the gun's plunger rod by pressing the thumb release lever and pulling the rod fully backward. Cut the cartridge tip and fit the nozzle. Cut to a 5mm opening — this provides approximately 3 metres of coverage per bead. Start small; you can always enlarge the opening but you cannot reduce it. Pierce the internal seal by inserting a long nail or wire through the nozzle tip. Push firmly until the seal breaks. Without this step, no adhesive will flow regardless of trigger pressure. Load the cartridge nozzle-forward into the gun's cradle, ensuring the base sits flush against the plunger plate. Squeeze the trigger repeatedly while pointing at scrap material until adhesive appears at the tip.

For 680g Sausages: Pull the plunger rod fully back, remove the gun's front cap, insert the sausage nozzle-end forward, replace the cap, cut and pierce the nozzle as above, then pump the trigger until adhesive flows. The flexible sausage packaging collapses as you dispense, unlike rigid cartridges. Note: When you release the trigger, adhesive may continue to flow briefly due to residual pressure. Use the pressure release lever (if your gun has one) or twist the gun barrel to stop flow between beads. Practice Your Bead Control on Scrap Material Never apply your first bead to your actual project. Practise on scrap material identical to your project substrate to develop consistent technique. Hold the caulking gun at a 45-degree angle to the surface with the nozzle tip close to the material. Squeeze the trigger with steady, even pressure while moving the gun smoothly along your intended line. Aim for a consistent bead from the 5mm nozzle opening — this delivers approximately 3 metres of coverage per bead. Common beginner issues: beads with gaps result from inconsistent trigger pressure or moving too fast; excessive adhesive pooling comes from moving too slowly; wavy beads result from watching the gun body instead of the nozzle tip. Focus your eyes ahead of where you're applying, not directly at the nozzle. Practise until you can lay a consistent bead with controlled start and stop points. The adhesive you use during practice prevents costly errors on your actual materials. Apply the Right Amount in the Right Pattern Follow these application patterns for best results: For joists, studs, or battens: Apply a bead along the length of the joist, stud, or batten. For broad flat surfaces: Apply beads every 40cm in a zig-zag pattern. On a standard 1200mm wide sheet, this translates to approximately 3 beads across the width. Focus adhesive placement where the sheet contacts framing members or substrates. Bead size: Cut the nozzle to a 5mm opening. This delivers approximately 3 metres of coverage per continuous bead. Edge treatment: Avoid applying adhesive too close to material edges. When materials are pressed together, the adhesive spreads outward. Edge beads create visible squeeze-out that requires cleanup. Important limitation: Avoid use in tightly clamped joints (e.g. cabinet making joinery). This adhesive is designed for construction bonding with nails, screws, or moderate clamping — not for high-pressure cabinetry joints that squeeze out all adhesive and starve the bond. Position Materials and Fix in Place After applying adhesive, position your materials and press firmly together. Fix with sufficient nails, screws, or clamping to hold load and achieve contact over the total bond area. The 20-minute repositioning window: The adhesive is repositionable for up to 20 minutes after fitting. This gives you a generous window to check alignment, make adjustments, and get things right before the bond begins to develop. After 20 minutes, repositioning becomes difficult and may compromise bond quality. Fixings options: Nails, screws, or clamping — not clamping alone. For most construction applications, temporary nails or screws are the practical choice as they hold materials in position while the adhesive cures and can be left in place permanently. For high stress applications, use with mechanical fasteners. Key reminder: Do not use as the sole bonding agent for structural bonding. Always combine with appropriate mechanical fasteners for any load-bearing application. For large or heavy materials, use a helper to control initial placement. Press materials together with firm, even pressure across the entire bonded area. You should see minimal squeeze-out at edges — excessive squeeze-out indicates over-application. Allow Proper Cure Time Minimum 24 hours before removing any temporary fasteners or clamping. Usually a strong bond is achieved in 24 hours and continues to strengthen over 2–3 days. Full cure: 7 days. The tensile strength reaches 1MPa after 7 days. Allow the full 7 days before subjecting bonds to maximum stress, water exposure, or vibration. Factors that extend cure time: Expect longer times for thicker applications, less porous surfaces, and in cold weather. The adhesive performs in application temperatures from 5°C to 35°C and service temperatures from -20°C to 100°C, but cold conditions slow everything down. Clean Up Uncured adhesive: Remove with mineral turpentine. Wipe tools, surfaces, and any squeeze-out promptly while adhesive is still wet. Pour mineral turpentine onto clean rags — do not pour directly onto surfaces. Replace rags as they become saturated. Cured adhesive: Once cured, the adhesive cannot be dissolved. Remove by scraping or sanding. On finished surfaces, mechanical removal may cause damage, so clean up uncured adhesive immediately. Skin contact: If adhesive contacts skin, wipe immediately with dry rags to remove bulk material, then clean with mineral turpentine followed by soap and water. This product causes skin irritation (H315) — nitrile gloves prevent this entirely. Contaminated PPE: Wash contaminated clothing and other protective equipment before storing or re-using. Know the Limitations Selleys Liquid Nails Original has specific limitations that must be respected for safe and effective use:

Avoid use in tightly clamped joints (e.g. cabinet making joinery) — the adhesive needs to maintain adequate thickness in the bond line; high clamping pressure squeezes out too much material Not for use on mirrors — use Liquid Nails Mirror Metal and Glass instead Not for metals heated by direct sunlight — bonds weaken at higher temperatures; use Liquid Nails Mirror Metal and Glass instead Not for styrene foam — use Liquid Nails Fast Grab instead Do not use as the sole bonding agent for structural bonding — always combine with mechanical fasteners for structural applications Not for permanent water immersion

The Product Page adds: 7. Not suitable for polyethylene, polypropylene, or Teflon® — these materials resist bonding from most construction adhesives Troubleshoot Common Problems Problem: Adhesive won't dispense despite trigger pressure Internal seal not punctured, or nozzle opening too small. Remove the cartridge, verify the seal is broken with a wire or nail, and enlarge the nozzle opening if necessary. Problem: Materials slide apart after positioning Insufficient fixings or contaminated surfaces. Fix with sufficient nails, screws, or clamping to hold load and achieve contact over the total bond area. Ensure surfaces are free from oil, grease, and dust. If materials have separated, clean both surfaces, allow to dry, reapply adhesive, and fix immediately with adequate mechanical support. Problem: Weak bond after full cure time Most likely caused by contaminated surfaces, inadequate fixings during cure, or bonding an incompatible material. Check whether the substrate is polyethylene, polypropylene, Teflon, or styrene foam — these are excluded materials. Check whether metal substrates are exposed to direct sunlight — bonds weaken at higher temperatures. For structural applications, ensure mechanical fasteners are used alongside the adhesive. Problem: Bond failure on foam If the foam is styrene foam, this product is not suitable. Use Liquid Nails Fast Grab instead. Other foam types (polyurethane foam, for example) should bond successfully. Step-by-Step Application Summary

Put on full PPE: Safety shoes, overalls, nitrile rubber gloves, safety glasses, and respirator where inhalation risk exists. Eliminate ignition sources both in and near the work area. Do not smoke. Prepare surfaces: Ensure surfaces are free from oil, grease, and dust. Wipe off any pooled water from wet timber. Cut cartridge tip, fit nozzle, and cut to a 5mm opening. Apply bead along the length of joist, stud, or batten. On broad flat surfaces, apply beads every 40cm in a zig-zag pattern. Position pieces and press firmly together. Fix with sufficient nails, screws, or clamping to hold load and achieve contact over total bond area. Materials are repositionable for up to 20 minutes after fitting. Allow adhesive to set: minimum 24 hours before removing any temporary fasteners or clamping. Use with mechanical fasteners in high stress applications. Full cure: 7 days. Expect longer for thicker applications, less porous surfaces, and cold weather. Clean up uncured adhesive immediately with mineral turpentine. Cured adhesive can be removed by scraping or sanding.

Your Pre-Application Checklist Safety:

Full PPE on: safety shoes, overalls, nitrile rubber gloves, safety glasses, respirator (AS/NZS 1715 and 1716 where inhalation risk exists) All ignition sources eliminated both in and near the work area (flash point is -15°C) No smoking Explosion-proof equipment, non-sparking tools, grounding in place Fire extinguisher accessible (alcohol resistant foam or dry agent) Adequate ventilation confirmed (natural ventilation adequate under normal conditions) Eyewash station and safety shower close to workstation

Materials:

Confirmed: no polyethylene, polypropylene, Teflon, styrene foam, or mirrors in the project Confirmed: no metals that will be heated by direct sunlight Confirmed: not for permanent water immersion Confirmed: not sole bonding agent for structural applications — mechanical fasteners planned Confirmed: not a tightly clamped joint (e.g. cabinet making joinery) Both surfaces free from oil, grease, and dust Pooled water wiped from wet timber Nails, screws, clamps, or bracing staged and ready

Application:

Caulking gun loaded and tested on scrap material Nozzle cut to 5mm opening Practice bead completed on scrap substrate Bead spacing planned: every 40cm on broad flat surfaces Mineral turpentine and cleanup supplies staged Timer or clock available: minimum 24 hours cure before removing temporary fasteners

First Aid Information In case of emergency, refer to the Safety Data Sheet. Key first aid measures: If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766). IF exposed or concerned: Call a POISON CENTER or doctor. Have product container or label at hand. Inhalation: Remove victim from exposure — avoid becoming a casualty. Remove contaminated clothing and loosen remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest until fully recovered. Seek medical advice if effects persist. Skin contact: If skin or hair contact occurs, immediately remove contaminated clothing and flush skin and hair with running water. Continue flushing for 15 minutes. For gross contamination, immediately drench with water and remove clothing. For skin burns, cover with a clean dry dressing. If blistering occurs, do NOT break blisters. If swelling, redness, blistering, or irritation occurs, seek medical assistance. Eye contact: Hold eyelids apart and flush eyes continuously with running water for at least 15 minutes. Seek medical attention. Ingestion: Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass of water to drink. Never give anything by mouth to an unconscious patient. If vomiting occurs, give further water. Seek medical advice. Emergency telephone: Australia — 1800 220 770; New Zealand — 0800 220 770. References

Selleys Liquid Nails Original Technical Data Sheet (Version 3.1, 27/03/2023) — Product description, packaging, uses, features, technical details, surface preparation, directions for use, coverage, clean up, limitations Selleys Liquid Nails Original Safety Data Sheet (Version 12.0, 13 March 2024, Ref: SELGHSEN000129) — Hazard identification, PPE requirements, first aid, composition, handling/storage, physical properties, transport Selleys Liquid Nails Construction Adhesive Product Page — Product features, technical details, limitations, directions for use

Label Facts Summary

Disclaimer: All facts and statements below are sourced from official Selleys documentation (Technical Data Sheet, Safety Data Sheet, and Product Page). Consult the full SDS and TDS for complete information. This is not professional safety advice.

Verified Label Facts

Product name: Selleys Liquid Nails Original Brand: Selleys (a division of DuluxGroup (Australia) Pty Ltd) ABN: 67 000 049 427 Product type: Solvent-based construction adhesive Description: High strength multipurpose construction adhesive Colour: Brown / Beige Package sizes: Tube 100g, Cartridge 320g, Cartridge 375mL, Sausage 680g Suitable materials: Timber, plasterboard, MDF, particleboard, masonry, concrete, tiles, ceramics, metals, plastics*, rubber, glass Not suitable for: Polyethylene, polypropylene, Teflon, styrene foam, mirrors, metals heated by direct sunlight Do not use as: Sole bonding agent for structural bonding Avoid: Tightly clamped joints (e.g. cabinet making joinery) Not for: Permanent water immersion Indoor/Outdoor: Both (per Product Page Features) Water resistance: Excellent Strength: High strength (Tensile 1MPa after 7 days, AS2329) Sag resistance: Less than 6mm (AS2329) Density: 1.15 Flexible: Yes Wet and dry timber: Yes Easily extrudable at low temperatures: Yes Coverage: Approximately 3m using a 5mm diameter bead Nozzle opening: 5mm Bead spacing (broad surfaces): Every 40cm Repositioning time: Up to 20 minutes after fitting Fixings: Nails, screws, or clamping; mechanical fasteners in high stress applications Cure time (strong bond): 24 hours (continues strengthening 2–3 days) Cure time (full strength): 7 days Paintable: Yes, when fully cured Application temperature: 5°C to 35°C Service temperature: -20°C to 100°C Standard: AS-2329 (1999) Clean-up (uncured): Mineral turpentine Clean-up (cured): Scraping or sanding Signal word: Danger Hazard classifications: Flammable Liquids Cat 2; Skin Irritation Cat 2; Eye Irritation Cat 2A; STOT-SE Cat 1 H225: Highly flammable liquid and vapour H315: Causes skin irritation H319: Causes serious eye irritation H370: Causes damage to organs PPE: Safety shoes, overalls, gloves (nitrile rubber), safety glasses, respirator (AS/NZS 1715 and 1716) Engineering: Natural ventilation adequate under normal use conditions Flash point: -15°C Specific gravity: 1.12 to 1.16 Vapour density: Greater than 1 (heavier than air) Solubility: Insoluble in water; soluble in organic solvents Autoignition temperature: Greater than 200°C Dangerous Goods Class: 3 (Flammable Liquid) UN No: 1133 Packing Group: III Hazchem Code: 3Y Marine pollutant: Yes Composition: Naphtha petroleum hydrotreated light 10–30%; Phenol 2,2-methylenebis[6-(1,1-dimethylethyl)-4-methyl] less than 1% Storage: Cool, dry, well-ventilated, out of direct sunlight, away from foodstuffs, away from heat/ignition sources, locked up, container upright, closed when not in use Made in: Australia Condition: New Currency: AUD

General Product Claims

High strength multipurpose construction adhesive Strong and lasting bond on most building substrates Water and weather resistant Flexible after curing Bonds wet and dry timber Easily extrudable at low temperatures Paintable when fully cured Meets AS-2329 (1999) Made in Australia